Dear All,

For your information. I am in the midst configuring outbound/inbound and trunk for elastix server. Furtherrmore, The elastix server has been setup with sangoma A200-R and plug in with PSTN line into FXO port 4. I was unable to make outbound call and receive call. I am keen to get advised from you how to setup. Eventhou, I read many times the elastix without tears and freepbx 2.5 manual. But still cannot resolved the problem. Kindly advised. Thanks.

Paste the output for:
lspci
rpm -qa | grep dahdi | sort
uname -a
lsdahdi
asterisk -rx "dahdi show channels"
also paste the CLI output (asterisk -r) when you try to do an inbound/outbound call

hi.. herewith i enclosed you the output..


[root@centrisk ~]# lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02)
00:19.0 Ethernet controller: Intel Corporation 82562V-2 10/100 Network Connection (rev 02)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02)
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02)
00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
03:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa)
04:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card
[root@centrisk ~]# rpm -qa | grep dahdi | sort
dahdi-2.4.1.2-10
dahdi-devel-2.4.1.2-10
kmod-dahdi-2.4.1.2-10
[root@centrisk ~]# uname -a
Linux centrisk 2.6.18-238.12.1.el5 #1 SMP Tue May 31 13:23:01 EDT 2011 i686 i686 i386 GNU/Linux
[root@centrisk ~]# lsdahdi
### Span 1: WRTDM/0 "wrtdm Board 1" (MASTER)
1 FXS FXOKS (SWEC: MG2)
2 FXS FXOKS (SWEC: MG2)
3 FXO FXSKS (SWEC: MG2) RED
4 FXO FXSKS (SWEC: MG2)
5 EMPTY
6 EMPTY
7 EMPTY
8 EMPTY
9 EMPTY
10 EMPTY
11 EMPTY
12 EMPTY
13 EMPTY
14 EMPTY
15 EMPTY
16 EMPTY
17 EMPTY
18 EMPTY
19 EMPTY
20 EMPTY
21 EMPTY
22 EMPTY
23 EMPTY
24 EMPTY
[root@centrisk ~]# asterisk -rx "dahdi show channels"
Chan Extension Context Language MOH Interpret Blocked State
[root@centrisk ~]# asterisk -r
Asterisk 1.8.11.0, Copyright (C) 1999 - 2012 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type 'core show license' for details.
=========================================================================
Connected to Asterisk 1.8.11.0 currently running on centrisk (pid = 5507)
Verbosity is at least 3
centrisk*CLI>
centrisk*CLI>


kindly advised. thanks.

Your card is not correctly configured.
Go to Hardware detector, and check the option to write on chan_dahdi, then execute again the previous commands